Ditch Lights

Ditch Lights for Trucks: Where to Mount Pod Lights (No Drilling Required)

TYPE S Elevate pod light mounted at the A-pillar as a ditch light with pod lights on the roof rack

Ditch lights are one of the most useful lighting upgrades for a truck, Jeep, or SUV. A pair of pod lights near the A-pillars lights up the sides of the trail, so you can see turns, ruts, and obstacles your headlights miss. Here’s what ditch lights are, where to mount pod lights, and how to install them without drilling using the TYPE S Universal Pod Light Hood Mount Kit.

TYPE S Elevate round pod light mounted at the A-pillar as a ditch light


What Are Ditch Lights?

Ditch lights are auxiliary lights mounted near the base of the windshield, usually at the A-pillars or hood seams, and aimed slightly outward. Instead of lighting straight ahead like a light bar, they light the edges of the trail and the “ditches” on either side. That helps on tight, winding trails where your headlights point past the turn.


Spot vs Flood Ditch Lights

  • Flood ditch lights – Wide coverage close to the vehicle. The most popular choice for ditch lights.
  • Combo ditch lights – A mix of reach and width, good if you drive both slow trails and faster dirt roads.
  • Spot ditch lights – More reach, less width. Better as driving lights on the bumper.

For more on beam patterns, read Spot vs Flood vs Combo Light Bar.


Where to Mount Pod Lights

  • A-pillars or hood seams – Classic ditch light position for lighting the sides of the trail.
  • Front bumper – Good for spot or combo driving lights.
  • Roof rack or crossbar – Light from a high position, and the spot where amber clearance modes are meant to be mounted.
  • Rear bumper or bed rack – Flood lights for backing up, camp, and loading.

For more ideas, see Don’t Know Where to Mount Those New Pod Lights? We Can Help.


No-Drill Ditch Lights: TYPE S Universal Pod Light Hood Mount Kit

Most ditch light brackets need holes drilled in your vehicle. The TYPE S Universal Pod Light Hood Mount Kit clamps onto the hood seam instead, so there are no permanent modifications.

  • No-drill installation – Clamps securely to the hood seam.
  • 304 stainless steel – Strong and corrosion-resistant.
  • Rubber-padded contact points – Helps keep the mount secure and reduce vibration and rattles.
  • Adjustable – Vertical and horizontal angle adjustment for aiming.
  • Universal fit – Fits most pod and cube lights and light bars up to 6 inches.
  • 2-pack with hardware – Everything you need for a pair of ditch lights.

For the best ditch lighting, mount the brackets near the A-pillars.

TYPE S universal no-drill pod light hood mount kit clamp-on brackets


Best TYPE S Elevate Pod Lights for Ditch Lights

All of these have die-cast aluminum housings and an IP67 dust and waterproof rating.

TYPE S Elevate 6 inch combo beam pod light with 4,050 raw lumens at 6500K


How to Install Ditch Lights Without Drilling

  1. Pick your spot – Find the hood seam near each A-pillar. Make sure the hood can still open and close freely.
  2. Clamp the brackets – Install the hood mounts with the rubber pads and pressure plates, following the kit instructions.
  3. Attach the pod lights – Bolt each light to its bracket.
  4. Run the wiring – Use the harness included with your light set, the Elevate 2-Light Wiring Harness, or the LYNX 6 Switch Panel. Keep wires clear of the hood hinge and moving parts.
  5. Aim the lights – Angle them slightly outward and down to light the sides of the trail.
  6. Test every mode – Check each mode before you head out.

Watch: How to Install TYPE S Elevate 3" Cube Pod Lights

Watch: How to Install the TYPE S Elevate 6" Combo Pod Light


Are Pod Lights Street Legal?

It depends on the light and how you use it. TYPE S Elevate pod lights include on-road modes, such as an SAE J581 auxiliary mode and DOT clearance or parking light modes, and they’re DOT/SAE compliant when installed in pairs as directed. Off-Road mode is for off-road use only. Lighting laws vary by state, so check your local rules. Learn more in Are Off-Road Lights Street Legal?


Ditch Lights FAQ

Do I need to drill holes to install ditch lights?

Not with the TYPE S Universal Pod Light Hood Mount Kit. It clamps onto the hood seam with no drilling.

What size lights fit the TYPE S hood mount kit?

Most pod and cube lights and compact light bars up to 6 inches.

Should ditch lights be spot or flood?

Flood or combo beams are the most common choice, because ditch lights are meant to light the sides of the trail.

Do the Elevate pod light sets include a wiring harness?

The 3" Combo Cube, 3.5" Spot Round, and 4" x 3" Flood sets include a harness kit. For single lights or more complex setups, use the 2-Light Wiring Harness or LYNX 6.


Conclusion

Ditch lights help you see the sides of the trail, and with the TYPE S Universal Pod Light Hood Mount Kit you can add them without drilling. Pair the mounts with TYPE S Elevate pod lights for bright, weatherproof lighting with built-in on-road modes.


Related Reading

Reading next

TYPE S x Formula DRIFT carbon fiber shift knob with red FD logo in a car interior lit with red ambient light

Leave a comment

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.